English
简体中文
Español
Русский
日本語
Deutsch
Français
Português
Home
Products
Household water purifier-Whole House Water Filter System
Commercial water purifier
Water treatment equipment
Outdoor water purifier
Industrial water purifier system
Air Purifier
Water Softener System
Pre Filtrations
Whole House Sediment Filter Filter Cartridge RO membrane
Case
Case Example
Feedback
News
About Us
English
Home
Products
household water purifier-whole house water filter system commercial water purifier water treatment equipment industrial water purifier system air purifier water softener system pre filtrations
Case
case example
Feedback
News
About Us
en
简体中文 Español Русский 日本語 Deutsch Français Português
Water purification information
Home > Water purification information

Work flow and work requirements of softened water equipment

Views : 87027
Update time : 2021-09-26 11:53:54
（1) Work flow of softened water equipment
Work (sometimes called water production, the same below), backwashing, salt absorption (regeneration), slow flushing (replacement), and fast flushing. All the processes of different softened water equipment are very similar, but due to the actual process or the need for control, there may be some additional processes. Any water softening equipment based on sodium ion exchange is developed on the basis of these five processes (among which, fully automatic water softening equipment will increase the brine reinjection process).

Backwashing: After working for a period of time, the equipment will intercept a lot of dirt brought by the raw water on the top of the resin. After the dirt is removed, the ion exchange resin can be completely exposed and the regeneration effect can be guaranteed. The backwashing process is that water washes in from the bottom of the resin and flows out from the top, so that the dirt intercepted by the top can be washed away. This process generally takes about 5-15 minutes. Salt absorption (regeneration): the process of injecting salt water into the resin tank. The traditional equipment uses a salt pump to inject the salt water, and the fully automatic equipment uses a dedicated built-in ejector to suck the salt water (as long as the inlet water has a certain pressure) . In the actual working process, the regeneration effect of salt water flowing through the resin at a slower speed is better than that of simply soaking the resin with salt water. Therefore, the softened water equipment is regenerated by the method of slowly flowing salt water through the resin. This process generally requires 30 About minutes, the actual time is affected by the amount of salt used. Slow flushing (replacement): After the salt water flows through the resin, the process of slowly flushing all the salt in the resin with raw water at the same flow rate is called slow flushing, because there are still a large number of functional groups in the flushing process. Calcium and magnesium ions are exchanged by sodium ions. According to actual experience, this process is the main process of regeneration, so many people call this process replacement. This process is generally the same as the salt absorption time, which is about 30 minutes. Quick flushing: In order to thoroughly flush the remaining salt, the resin should be flushed with raw water at a flow rate close to the actual work. The final effluent of this process should be soft water that meets the standard. Under normal circumstances, the fast flushing process is 5-15 minutes.
　

（2) Technical indicators and work requirements of softened water equipment:

Inlet water pressure: 0.18-0.6Mpa

Working temperature: 1-55℃ Source water hardness: <8mmol/L

Operation mode: automatic/manual water hardness: ≤0.03mmol/L

Regeneration agent: NaCL Regeneration method: downstream/countercurrent

Exchanger: 001*7 strong acid ion exchange resin

Control method: time/flow power supply: 220V/50Hz
Previous :
Next :
Related News
Read More >>
Analysis of common problems of reverse osmosis water equipment operation Analysis of common problems of reverse osmosis water equipment operation
Oct .29.2024
Reverse osmosis equipment is an important part of pure water equipment, purified water equipment, ultrapure water equipment, and also equipment system operation is more prone to problems.
The following are common reverse osmosis equipment problems and causes.
Do you know what is the most reasonable recovery rate setting for RO system? Do you know what is the most reasonable recovery rate setting for RO system?
Oct .28.2024
When discussing design options with peers and customers, the question of the reasonableness of the system's recovery rate setting often comes up. The essence of the problem is to set the recovery rate has exceeded the upper limit of the recovery rate of the system (limit recovery rate).
Do you know the difference between ultrapure water equipment and pure water equipment? Do you know the difference between ultrapure water equipment and pure water equipment?
Oct .28.2024
Do you know the difference between ultrapure water equipment and pure water equipment?
Here Susan will let you know what the differences between them.
Reverse osmosis ultrapure water equipment common faults (with solutions) Reverse osmosis ultrapure water equipment common faults (with solutions)
Oct .25.2024
Reverse osmosis ultrapure water equipment is a kind of equipment used to remove impurities and pollutants in water, but it is inevitable that it will encounter some problems in the course of its usual operation and use, so how should it solve these problems? The following are some common water purifier problems with corresponding solutions:
Xiamen Ouge Digital Technology Co., Ltd
en
简体中文 Español Русский 日本語 Deutsch Français Português
Susan Susan
Susan
Susan Huang